How to play Train Tracks
- Find the Start (S) and End (E) stations at the edge of the grid.
- Read each row and column number: it is how many cells in that line hold track.
- Mark an X in every cell that cannot hold track, starting with lines numbered 0.
- Extend the track from cells that have only one way to continue.
- Finish with one unbroken track from S to E and every count matched.
Train Tracks rules
The board
- The grid is 5×5 to 7×7 in Gridwise. A green Start cell (S) and a red End cell (E) mark the two ends of the line.
- Each row and column has a number at its edge: the exact count of cells in that line that hold a piece of track.
- Some cells start with given pieces, shown with a rivet dot. They cannot be changed.
Track pieces
- There are six pieces: two straights (across and down) and four curves (each joining two neighbouring sides of a cell).
- Each track cell connects to exactly two neighbours, except the Start and End, which are the ends of the line.
Restrictions
- The track may not cross itself, branch or form a closed loop.
- Every piece must be part of the one track from Start to End: no stray pieces.
- Mark a cell with an X to note that it holds no track.
Winning
- One connected track joins Start to End, and every row and column count matches.
Train Tracks techniques, from first game to expert
Beginner
1. Clear the zero lines
A row or column numbered 0 holds no track at all. Fill it with X marks first; it often cuts the board into a narrow corridor.
Beginner
2. Fill the lines with no spare cells
If a line's number equals the cells still open in it, every one of those cells is track. On a 6×6 board, a 6 means the whole line.
Beginner
3. Leave the station correctly
A station is an end of the line, so it joins exactly one neighbouring track cell. As soon as X marks and the edge leave a station a single open side, the cell on that side is track.
Improving
4. Use cells with only two open neighbours
A track cell has to connect to two neighbours. If X marks and the edge leave it only two open sides, both must be used, which fixes the piece.
Improving
5. Avoid early loops
When two loose ends of track sit side by side, joining them would close a loop that does not reach both stations. That joining move is forbidden, so the ends must turn elsewhere.
Expert
6. Keep Start connected to End
A piece that walls off one station from the other is impossible. When a choice would trap the track in a dead-end pocket, take the other option.
Expert
7. Combine a row and a column
Where a row that is almost full crosses a column that is almost empty, compare what each still needs. Often the crossing cell is the only one that satisfies both counts. On Hard levels, a single short trial settles the rest.
A worked example
Picture a 5×5 board. Start (S) is the cell in row 2, column 1, on the left edge. End (E) is the cell in row 5, column 4, on the bottom edge. The row counts, top to bottom, are 0, 1, 4, 3, 3. The column counts, left to right, are 4, 3, 1, 3, 0. Both stations count as track cells.
- Zero lines. Row 1 and column 5 hold no track. Mark all their cells with X.
- Row 2 (count 1). S is its only track cell, so the rest of row 2 is X.
- Leaving S. Up is row 1 and right is row 2, both X. The track leaves S downward.
- Column 1 (count 4). Row 1 is X, so rows 2 to 5 are all track. The corner cell at row 5, column 1 has only two open sides, up and right, so the track turns right into row 5, column 2.
- Row 5 (count 3). Columns 1, 2 and 4 (E) make 3. Column 3 in row 5 is X. E therefore connects upward, to row 4, column 4.
- The cell at row 5, column 2. It came in from the left; right is X, so it turns up into row 4, column 2.
- Row 4 (count 3). Columns 1, 2 and 4 are track, which is the full count. Row 4, column 3 is X.
- Column 4 (count 3). Rows 4 and 5 are track and row 2 is X, so the third cell is row 3. The cell at row 4, column 4 runs straight up and down.
- Row 4, column 2. It cannot turn into column 1 (that cell already runs straight down) or into the X at column 3, so it goes up to row 3, column 2.
- Row 3 (count 4). Columns 1, 2 and 4 are track; column 5 is X, so the fourth cell is column 3. Column 3’s count of 1 is now met.
The route reads: S, down column 1 to the bottom corner, right one cell, up two cells, right along row 3 to column 4, then down to E. Every step came from a count or from a cell with only two open sides. Nothing was guessed.
History and variants
Railway-route puzzles counted by rows and columns appear in puzzle books under names such as Tracks and Train Tracks. Some versions include crossing pieces or have no marked stations; in Gridwise the route always runs from a green Start to a red End with no crossings.
Where to play Train Tracks
Gridwise
Logic puzzles in one calm app
- Train Tracks is one of Gridwise's original puzzles, with 2,000 levels.
- Boards run from 5×5 to 7×7; chapters 7 to 20 use 6×6 and 7×7.
- Easy levels give at least 4 track pieces, Medium 2 or 3, and Hard 0 or 1.
- Every level has exactly one solution that you can reach by reasoning.
- A typical solve takes about 5 minutes, and a mistake is shown and explained, never punished.
Questions about Train Tracks
What are the rules of the Train Tracks puzzle?
Lay one track from the Start station to the End station so each row and column holds exactly the number of track cells shown at its edge. The track never crosses itself, branches or loops.
What does the number next to a row mean?
It is how many cells in that row contain a piece of track, whether straight or curved.
Can the train track cross itself?
No. There are no crossing pieces. Each cell holds either nothing, a straight piece or a curve.
Do I have to use the given pieces?
Yes. Given pieces, marked with a rivet dot, are part of the solution and stay where they are.
Is Train Tracks the same as the Tracks puzzle?
They share the idea of a single route counted by rows and columns. Gridwise's version has a marked Start and End and six track pieces, with no crossings.
Facts checked against the game's own design documents on .